Pneumatic Lockout

KRM Pneumatic Lockout fits virtually all pneumatic fittings. Manufactured from stainless steel the pneumatic lockout is applied to the fitting and prevents it from being reconnected to the pressurised air sources that are anti-rust and corrosion resistance.

Material – Stainless Steel

Holes for cord – Nine holes of different diameter, decreasing in diameter respectively

Color – Stainless Steel Finish

Weight – 50 gm

Material – Stainless Steel with powder coating

KRM Pneumatic Lockout is easily applied on the male fitting, isolating equipment from all compressed air sources, hole in center of device allows for permanent storage on an air hose and a loop on the side can be used to hang the hose and lockout device,

Lockout accepts padlocks with 1/4" or 9/32" shackle size.

Accommodation – Device accommodate the majority of 1/4", 3/8" and 1/2" male fittings

Holes for chord – Six holes of different diameter

Color – Red and as per the requirement

Weight – 50 gm

KRM Mini Pneumatic lockout construct in two parts that Completely encloses pneumatic lockout of mini size to prevent accidental reconnection.

Material – ABS with printed label

Locking slots – Three hole to place the Lock

Size – length 90 mm, width 50mm, diameter 25 mm excluding hinge and lockoing arrangement. Diameter of power chord that is different for both side.

One side 14 mm, another side 19 mm.

Color - Yellow, Red or any other color as per requirement.

Weight - 50 gms

KRM Mini Pneumatic lockout constructs in two parts that Completely encloses pneumatic lockout of mini size to prevent accidental reconnection. Material – ABS with printed label •Locking slots – Three hole to place the Lock

Size – length 90 mm, width 50mm, diameter 25 mm excluding hinge and locking arrangement.

The diameter of power chord that is different for both side.

One side 14 mm, another side 19 mm.

Color - Yellow, Red or any other color as per requirement.

Weight - 50 gms

KRM Large Pneumatic Lockout isolates potentially hazardous energy without costly tool modifications or inconvenient in-line valves.

Material - Poly Propylene.

Holes for Chord - One hole of 25 mm diameter on both sides.

Locking Slots - 4 holes to latch with lock for group isolation.

Complete Outer Size - Length - 194 mm and width 64 mm.

Inner Size - Length 184 mm and width - 60 mm.

Color - Red or can make any color as per volume required.

Weight - 260 gms

KRM Dual Large Pneumatic Lockout isolates potentially hazardous pneumatic energy without costly tool modifications or inconvenient in-line valves.

Material – Poly Propylene

Holes for chord – One hole of different diameter on both sides

Isolate Large Plugs of Size – diameter 118 mm, length – 250 mm

Locking slots – 11 hole to Latch with Lock for group isolation.

Complete Outer Size – length 256 mm, width 124 mm

Inner Size – length 250 mm, width 118 mm

Color – Yellow, Red Or any color make as per the quantity

Weight – 375 gm

Cylinder Device is used to lock pneumatic device. It does not require any extra tool for fixing only latched by the padlocks directly

Material – Poly Propylene with printed label

KRM Universal Multi-Device Lockout made by joining two parts that are designed to be used on high and low-pressure gas cylinders and control the cylinder by locking the regulator attachment, also useful for plug or chord lockout

Locking slots – One hole to place the Lock

Upper plates – Two or Three slots are attached with round rivet

Outer Size – diameter 88 mm (3.45”), length 155 mm (6.10”)

Can lockout equipment of size – 3.4” Width x 6” Length

Color – Yellow, Red Or any color make as per required quantity •Weight – 113 gm

Material – Strong Polycarbonate body
Color - Transparent Glass.
Outer height – In closed position 55 mm (± 10%)
Internal size – Upper part Height 38 mm X Diameter 44 mm, lower base part Height 15 mm X Diameter 45.5 mm
For KRM-K-TPL23-Cut out diameter size of lower base part 23.5 mm. It can also be extended up to 30 mm dia.
For KRM-K-TPL30-Cut out diameter size of lower base part 30 mm.
With holes for locking purpose 7.5 mm.
Weight - 30 gms.

Material – Strong Polycarbonate body
Color - Transparent Glass.
Outer height – In closed position 55 mm (± 10%)
Internal size – Upper part Height 38 mm X Diameter 44 mm, lower base part Height 15 mm X Diameter 45.5 mm
For KRM-K-TPL23-Cut out diameter size of lower base part 23.5 mm. It can also be extended up to 30 mm dia.
For KRM-K-TPL30-Cut out diameter size of lower base part 30 mm.
With holes for locking purpose 7.5 mm.
Weight - 30 gms.